Plumbing 101: A Guide to Bathtub Installation
Plumbing 101: A Guide to Bathtub Installation
Blog Article
They are making a few good pointers related to A Step-by-Step Guide to Installing a Bathtub in general in this content down below.
Installing a tub isn't precisely rocket science, however it does require solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard project. If the old tub is conveniently available, the task can move speedily; if you have to open a wall surface to get rid of the old tub and position the new tub, the job is a lot harder. In either instance, the task is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and also set in the new one. See to it you have actually qualified on your own for the job and also are comfortable trying it. Instead of working with a service provider to take over a halfway-completed task, it is better to take into consideration employing one before you start. Possibilities are you might require a professional plumber to make tube links.
This post will assist you install a new bathtub in your shower room if you have actually already bought a brand-new tub as well as do not need to transform the plan of your previous water supply pipes.
Your devices and product list ought to consist of the following:
Planning for the Setup
To start with, the supporting framework supplied with the bathroom ought to be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the flexible tap ports to the bottom of both taps making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, then the first thing you need to do is disconnect the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather troublesome because of the limited gain access to that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, position the bath tub in the required setting. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four little factors.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the bath tub till the spirit level reads level.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression join; after that do the same for the various other tap.
Turn on the water supply as well as examine all joints and new pipework for leakages and tighten them if required. Fill up the bath tub and also inspect the overflow electrical outlet and also the regular outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the producer's user's manual. Tiling and sealing around the tub should wait until the tub has been made use of a minimum of when as this will settle it right into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the tap and the other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Secure the faucet in position with the manufacturer supplied backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type should be attached to the tap finishes initially, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack a rigid seal, triggering the water to permeate the wall in between the bath and the tiling, leading to issues with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealant can crack fairly early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that write-up on How to Install a Bathtub Yourself from a friend on another web property. Please take the time to promote this blog post if you appreciated it. Thanks a bunch for your time. Visit again soon.
Real results? Dial! Report this page